德瑞姆燃气回流炉VisionXP +2450
Equipment Size (W*D*H): L4990×W1576×H1570mm
Equipment Weight:
Power Requirements: 三相 3×400VAC ±5% 50Hz, 58kW（5线制）
Air Source Requirements: 0.7~0.8MPa, 约333L/min（氮气，单轨耗量约20m³/h）
Equipment Introduction:德国 Rehm（锐德）VisionXP+ 2450 为强制对流回流焊，工艺腔长 2450mm，5 个预热区（1750mm）加 2 个峰区（700mm），峰区最高 350℃，冷却区 1050mm，单轨 50~400mm（可选 460/508mm），可选真空腔与 Pyrolysis 热分解。整机为 5 线制、连接负载 58kW；氮气供给压力 0.7~0.8MPa、单轨耗量约 20m³/h。平台尺寸 4990×1576×1570mm 与所需占地 7.86m² 相符，原记气源仅写 bar 值，已换算为 MPa 并补流量。Show More
Equipment Parameters
Equipment Documents
Parts List
Equipment Parameters
| PROCESS CHAMBER HEATING | |
|---|---|
type | type 523 |
Required area | 7,86m² |
Load per unit area | 400kg/m² |
Length | 2450mm |
Quantity of preheating zones | 5 |
Length of preheating zones | 1750mm |
Quantity of peak zones | 2 |
Length of peak zones | 700mm |
Max. permissible soldering temperature : preheating zones | 300°C |
Max. permissible soldering temperature : peak zones | 350°C |
Heat transfer through | Forced convection |
Gas circulation per heating zone | max.350㎥/h |
Warm up time | ca.30min/approx30min |
Cross profile (Delta T=Tmax _ Tmin) | ±2,5Kelvin |
| COOLING ZONE | |
|---|---|
Length
| 1050mm |
| PIN CHAIN CONVEYOR | |
|---|---|
Transport Level | 900±75mm |
Width, single conveyor ±0,5 mm / without CBS | 50–400mm;
Option1:50–460mm;
Option2:50–508mm |
Width, single conveyor ±0,5 mm / with CBS | 65mm–400mm;
Option1:100–460mm;
Option2:140–508mm |
Width, dual conveyor ±0,02 in | 65mm–213mm(216mm) |
Clearance above the conveyor | 30mm |
Pin chain support width | Standard3mm,optional5mm |
Tolerance conveyor speed | (1%per1800mm/min) |
| CENTRE SUPPORT | |
|---|---|
Lash heigt | Lash stand off:16mm |
Distance to fixed rail lowered | 20mm |
Center Support active Width | 50mm–340mm;
Option1:50–380mm;
Option2:50–390mm |
CBS Low(Parking Position) | 14mm |
| OPERATING DATA | |
|---|---|
Maximum noise level | 70dBA |
Room temperature | between59Fand89,6F |
Humidity | between30%and75% |
Oxygen of peak zones | <100ppm |
| VOLTAGE SUPPLY CONSUMPTION | |
|---|---|
Type of power system | 5-Wire-System |
Connected load | 58KW |
| COOLING WATER AT EXTERNAL COOLING | |
|---|---|
Connection | M28x1,5(22mm Cu Rohr/0,87in Cu Tube) |
Cooling water flow | between 10–20 l/min(according to temperature) |
Operating pressure | min.2bar–max.5ba |
Differential pressure between forward and return run | min.0,5bar |
| NITROGEN SUPPLY | |
|---|---|
Connection | M16x1(12mm Cu Rohr)/M16x1(12mm/0,472in Cu Tube) |
Nitrogen supply pressure | min.7bar–max.8bar |
Operating pressure | 5bar |
Nitrogen consumption single conveyor at < 200 ppm in peak at min. 1 PCB gap | ca.20㎥/h |
Nitrogen consumption double conveyor at < 200 ppm in peak zone at min. 1 PCB gap | ca.22㎥/h |
| EXHAUST PROCESS | |
|---|---|
Exhaust socket: diameter | 150mm |
Exhaust at min. 5 mbar underpressure | 400㎥/h |
Exhaust temperature | <50°C |
| System configuration VisionX-Series | |
|---|---|
Single lane | Cold condensation with cooler/filter units only nitro systems |
Pyrolysis | integr. cooling circuit and heat exchanger for
connection to ext. facility water supplies |
Stand-By-Mode | Transmission zone |
Software control for fan speed regulation |
| optional | |
|---|---|
Dual lane | Multi track |
2nd Pyrolysis | Bottom cooling |
PCU Power Cooling Unit | Internal cooling/elimination of heat emission |
Measurement power consumption | Measurement nitrogen consumption |
Supervision of volume flow with active readjustment | Product management |
Traceability packages | Process interlock |
ProCap | Profile Creator |
KIC implementation | RPI |
MES-Option ROI | SSP+ |
uick Exhaust | Pin in Paste |