Rehm 锐德 真空回流炉 VisionXP
设备尺寸(W*D*H): L6040×W1576×H1570mm
设备重量: 3600kg
电源要求: AC400V 3相 50Hz
气源要求: 0.7~0.8MPa（氮气）
设备简介:德国Rehm（锐德）VisionXP+对流回流焊系统，可选真空腔实现低空洞焊接，配EC风机、双热解+冷凝聚残渣管理、SSP+分区温控与ViCON软件，有单/双轨、氮气/空气版本。名称中“真空回流炉”对应带真空选配配置。尺寸、重量取自6预热+3峰值+1冷却区（Type 634）规格；电压原含±5%容差，规范为AC400V 3相50Hz；氮气压力7~8bar换算为0.7~0.8MPa。展开更多
设备参数
设备文档
配件清单
设备参数
| PROCESS CHAMBER HEATING | |
|---|---|
type | type 634 |
Required area | 9,52 m² |
Load per unit area | 400 kg/m² |
Length | 3150 mm |
Quantity of preheating zones | 6 |
Length of preheating zones | 2100 mm |
Quantity of peak zones | 3 |
Length of peak zones | 1050 mm |
Max. permissible soldering temperature : preheating zones | 300 °C |
Max. permissible soldering temperature : peak zones | 350 °C |
Heat transfer through | Forced convection |
Gas circulation per heating zone | max. 350m³/h |
Warm up time | ca. 30min/approx 30min |
Cross profile (Delta T = Tmax _ Tmin) | ± 2,5 Kelvin |
| COOLING ZONE | |
|---|---|
Length | 1400 mm |
| PIN CHAIN CONVEYOR | |
|---|---|
Transport Level | 900±75 mm |
Width, single conveyor ±0,5 mm / without CBS | Standard:50–400mm;
Option1:50–460mm;
Option2:50–508mm |
Width, single conveyor ±0,5 mm / with CBS | Standard:65–400mm;
Option1:100–460mm;
Option2:140–508mm |
Width, dual conveyor ±0,02 in | 65mm–213mm(216mm) |
Clearance above the conveyor | 30 mm |
Pin chain support width | Standard 3mm, optional 5mm |
Tolerance conveyor speed | (1 % per 1800 mm/min) |
| CENTRE SUPPORT | |
|---|---|
Lash heigt | Lash stand off: 16mm |
Distance to fixed rail lowered | 20 mm |
Center Support active Width | Standard:50–340mm;
Option1:50–380mm;
Option2:50–390mm |
CBS Low (Parking Position) | 14 mm |
| OPERATING DATA | |
|---|---|
Maximum noise level | 70 dBA |
Room temperature | between 59F and 89,6F |
Oxygen of peak zones | <100 ppm |
| VOLTAGE SUPPLY CONSUMPTION | |
|---|---|
Type of power system | 5-Wire-System |
Connected load | 73 KW |
| COOLING WATER AT EXTERNAL COOLING | |
|---|---|
Connection | M28x1,5(22mm Cu Rohr/0,87in Cu Tube) |
Cooling water flow | between 10–20l/min(according to temperature) |
Operating pressure | min.2bar–max.5ba |
Differential pressure between forward and return run | min. 0,5 bar |
| NITROGEN SUPPLY | |
|---|---|
Connection | M16x1(12mm Cu Rohr)/M16x1(12mm/0,472in Cu Tube) |
Nitrogen supply pressure | min.7bar–max.8bar |
Operating pressure | 5 bar |
Nitrogen consumption single conveyor at < 200 ppm in peak at min. 1 PCB gap | ca. 21m³/h |
Nitrogen consumption double conveyor at < 200 ppm in peak zone at min. 1 PCB gap | ca. 22m³/h |
| EXHAUST PROCESS | |
|---|---|
Exhaust socket: diameter | 150 mm |
Exhaust at min. 5 mbar underpressure | 400m³/h |
Exhaust temperature | < 50°C |
| System configuration VisionX-Series | |
|---|---|
Single lane | Cold condensation with cooler/filter units only nitro systems |
Pyrolysis | integr. cooling circuit and heat exchanger for connection to ext. facility water supplies |
Stand-By-Mode | Transmission zone |
Software control for fan speed regulation |
| optional | |
|---|---|
Dual lane | Multi track |
2nd Pyrolysis | Bottom cooling |
PCU Power Cooling Unit | Internal cooling/elimination of heat emission |
Measurement power consumption | Measurement nitrogen consumption |
Supervision of volume flow with active readjustment | Product management |
Traceability packages | Process interlock |
ProCap | Profile Creator |
KIC implementation | RPI |
MES-Option ROI | SSP+ |
uick Exhaust | Pin in Paste |